LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
I have a no start no crank problem that I can’t figure out. All worked fine besides a few things before I changed my starter. After putting in a new starter this started and totally lost. The batteries are fully charged and good, grounds and terminals are all clean and good, fuses good, mega fuses good, starter relay good. Only electronics working are some dash lights, radio, AC, headlights/taillights but no power windows/locks, dome lights, door dinging, or indicator line. Also have codes U0140, U0141, U0100 pulling up. Today I’m going to get a new ignition switch and NSBU switch and harness for the transmission. Might be why no indicator line. Everything I’ve been reading is pointing to the BCM but not for sure. Only things wrong with truck before I put in the new starter was parking assist off abs service trailer brake system messages ABS and park brake lights always on. Any help and suggestions will be much appreciated! I really can’t afford to take it to the dealership or a shop right now. https://uploads.tapatalk-cdn.com/202...dfe4256c6d.jpg
https://uploads.tapatalk-cdn.com/202...1d3a0bc6dd.jpg
https://uploads.tapatalk-cdn.com/202...60b593cc63.jpg
Sent from my iPhone using Tapatalk
Re: LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
Best I can guess is you may have fried something reconnecting the batteries. Im guessing there is an expensive fuse that has popped. My other '08 had a bad wire and fuse that needed to be replaced.
Sent from my SM-N960U using Tapatalk
Re: LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
Quote:
Originally Posted by
zamoramax
Best I can guess is you may have fried something reconnecting the batteries. Im guessing there is an expensive fuse that has popped. My other '08 had a bad wire and fuse that needed to be replaced.
Sent from my SM-N960U using Tapatalk
Do u know what fuse and wire it was? I checked all the fuses, jcase fuse, and mega fuses and relays under the hood and inside truck. Also replaced all the important fuses with brand new ones just in case
Sent from my iPhone using Tapatalk
Re: LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
Quote:
Originally Posted by
JoshPando82
Do u know what fuse and wire it was? I checked all the fuses, jcase fuse, and mega fuses and relays under the hood and inside truck. Also replaced all the important fuses with brand new ones just in case
Sent from my iPhone using Tapatalk
It was the mega fuses. And the wire from the fuse box to wherever.... hope this might help somehow.
Sent from my SM-N960U using Tapatalk
1 Attachment(s)
Re: LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
Quote:
Originally Posted by
zamoramax
It was the mega fuses. And the wire from the fuse box to wherever.... hope this might help somehow.
Sent from my SM-N960U using Tapatalk
Gotcha. Thanks ya I changed one of them and the others were good. I’m almost positive it’s my BCM. I lost communications to almost all of my modules. I bought a $350 Innova 5160rs scan advisor professional code reader with RepaorSolutions2. It’s pretty badass for the price. Anyways for some reason I have a bunch of water under my drivers side carpet and the insulation is soaked and water puddled up all on the wires running along the floorboard. Not sure if that has anything to do with it and could’ve got my BCM wet. Is there a test I can do to see if the BCM is working properly and be able to find out if that’s it or not? I took a cpl short videos but won’t let me upload on here to show what my dash is doing when I turn the key to on and all the water on floor and wires. FML nothing can everhttps://uploads.tapatalk-cdn.com/202...4f495695ee.png
be easy! Attachment 789
https://uploads.tapatalk-cdn.com/202...2092cf59fd.jpg
Sent from my iPhone using Tapatalk
Re: LMM ‘07 no start no crank, no indicator light! PLEASE HELP!!!
Quote:
Originally Posted by
JoshPando82
Gotcha. Thanks ya I changed one of them and the others were good. I’m almost positive it’s my BCM. I lost communications to almost all of my modules. I bought a $350 Innova 5160rs scan advisor professional code reader with RepaorSolutions2. It’s pretty badass for the price. Anyways for some reason I have a bunch of water under my drivers side carpet and the insulation is soaked and water puddled up all on the wires running along the floorboard. Not sure if that has anything to do with it and could’ve got my BCM wet. Is there a test I can do to see if the BCM is working properly and be able to find out if that’s it or not? I took a cpl short videos but won’t let me upload on here to show what my dash is doing when I turn the key to on and all the water on floor and wires. FML nothing can ever
https://uploads.tapatalk-cdn.com/202...4f495695ee.png
be easy!
Attachment 789
https://uploads.tapatalk-cdn.com/202...2092cf59fd.jpg
Sent from my iPhone using Tapatalk
I'm at a guessing point same as you and I don't want to be misleading.
As far as the water it could be the hole(s) on the roof.
My '08 leaks from the satellite antenna and my yellow markers in the middle.
Sent from my SM-N960U using Tapatalk